Car suddenly stalled is very scary It is important to find out the cause of the problem
Release time:
2021-11-12
Remember that time when you were just driving? Remember the many times you stalled your car? Do you still remember the poor coordination between the gas and the clutch? Remember the clutch is always lifted fast and stalled? The following follow the editor together to understand the car stalling in the end is how it ......
The reason why the car stalled:
1, automatic models will not easily appear the phenomenon of stalling, and manual models due to the driving level is not high, may often appear the phenomenon of stalling. But do not rule out the automatic car will not appear the phenomenon of stalling, the main reason is the use of poor quality fuel (many gas stations in order to obtain profiteering to sell impure oil) resulting in engine carbon and stalling.
2, in addition, for the new car (automatic) the reason for stalling is mainly caused by driving skills are not skilled enough, another possibility is that the car engine or oil problems, but for the new car, the engine itself is less likely to be a problem, most of the reasons for the oil problem.
3, finally for the old model, the reason for stalling in addition to driving skills are not skilled enough, that is, the use of substandard quality oil so that the engine set carbon and other causes of stalling.
Automatic car stalling troubleshooting methods:
Usually pay attention to the place: for the automatic car stalling phenomenon, the main is still the use of poor quality fuel caused. First, to the regular larger gas stations to add high grade oil, such as the use of 95 gasoline, although the price is much more expensive, but can protect the car longer life and exercise in good power. However, some car owners are greedy for cheaper to add 92 oil, although the price is lower, but in the future there may be problems. Secondly, go to a large qualified gas station to refuel!
Practical operation: the left hand grasps the steering wheel to stabilize the direction (because there is no power, so must be hard to stabilize), the right foot hard to step on the brakes to reduce the speed of the car as much as possible, and then quickly AT gear to N gear, (Note: traveling in the re-ignition must be in the N gear, can not be the D/R/P and other gears, or else, the car is either unable to fire, or the car transmission will be damaged), and then will be backed up the key, and then re-ignited! Then back off the key and re-start the engine, and then return the AT gear to D for normal driving.
Manual car stalling troubleshooting methods:
1, for the novice, halfway stalling is not a new topic, the main method of elimination on the fast break-in to improve their driving skills.
2, the use of high standard high quality qualified fuel.
3, thoroughly clean the oil circuit, including injectors, throttle, fuel tank, etc.. It is possible that the quality of the oil you add is not good, too much grease, blocked the oil circuit, the attack oil is not smooth.
4, for the car idling state of the fault cause of stalling is mainly due to too much dust in the air, the engine is running idle motor spool and throttle seat deposited with a lot of dirt, when the dirt accumulates too much, the engine will appear idle speed is too low, idle stability is poor, driving will be idling stalling. The solution to this problem is very simple: just clean the idle motor can be.
5, whether the oil circuit is smooth, which is also easy to cause halfway out.
6, long-term car parking is not used. In fact, avoid parking for a long time without using. In case of parking for a long time, you should do a thorough maintenance before re-use, change the oil, filter, etc., and check the fuel, circuit, etc. as appropriate. Your vehicle may have been parked for an extended period of time causing problems with lubrication or electrical circuits.
Latest News
Latest News
Get Free Counseling

We are a high-tech enterprise specializing in the R&D, production, sales, and service of precision die-casting components and multi-slide die-casting equipment.
Contact

marketing@changyincast.com

Lamar Central, 3800 North Lamar Blvd., Suite 200, Austin, Texas, USA 78756
Copyright©2024 C&Y DIE CASTING L.L.C. All Rights Reserved.